You may be wondering why the water in the toilet bowl won’t go down or has been slowing down and backing up. You might have tried plunging it with no luck. This blog post will show you a few different methods to unclog a toilet when all else fails. If one doesn’t work, try another until you find one that does! With patience and persistence, there’s hope for your problem yet!

Plunging the toilet won’t work

Plunging is one of the most common methods people try when they’re having a slow draining toilet. Using a plunger works because it creates suction to help push the water down the drain and break up any clogs that are in your pipes. If you don’t have success with this method after trying it a few times, it’s best to try other options. Let’s say you have a slow draining toilet and decide to plunge it, but the plunger doesn’t work; what do you do? You can buy a toilet auger that will help remove blockages from your pipes. This tool is shaped like an old-fashioned corkscrew, so it’s basically a plunger on a wire.

Don’t use harsh chemicals, especially if you have a septic tank.

Harsh chemicals can damage your toilet, your septic system, and it could even cause a bigger clog. They can remove the finish from your toilet bowl if you’re not careful when using them. It’s best to use milder or natural solutions first unless you know of no other options. If they don’t work, then try a harsher solution. Be careful when using these chemicals to unclog a toilet. If you’re not sure about what you’re doing, hire a professional to help you out.

Sea salt, baking soda, and vinegar are all great ways to unclog a toilet. Fill the bowl with one of these ingredients and swish it around with a toilet brush. Make sure you use enough until it covers the sides as well as the bottom of the toilet bowl. The natural acids in the vinegar will help dissolve grime build-up. Salt has the same effect, but it also helps to dissolve water deposits and mineral scales that can slow down your toilet. Just be careful with these methods because they won’t damage the inner workings of a toilet or septic tank like chemical solutions will.

Treat your toilet like a garden. Sometimes, the problem could be that you’re not keeping your toilet bowl clean enough. Over time, things such as hair and food particles can build up in there. You don’t want to remove everything from it every time you go to the bathroom, but you should make sure it’s looked over once a week. Look for things like limescale deposits and grime build-up to see if you need to scrub it out with a toilet brush.

Clean your toilet more frequently. If you have a septic tank, then it helps if you can keep the bowl clean by cleaning it at least once every 2 weeks. That way, things like hair and food won’t build up in there as much. Make sure that when you’re putting materials inside the toilet bowl, they don’t get stuck.

If you have a slow-running toilet, then it’s probably because the flapper is broken. This is a plastic piece that hangs over the opening of your toilet tank and seals it when you flush it. If this part broke or fell off, then the water will pretty much run non-stop until someone fixes it. Replace the flapper by taking off the tank lid and then unscrewing it from inside. You can purchase a new flapper at any home improvement store.

Cleaning your toilet bowl with vinegar once a month is a good way to keep limescale deposits from building up. It also helps to prevent rust and mineral buildup, as well as character build-up and grime. Make sure you pour enough in there to cover the bottom and sides of your bowl, then scrub it down with a toilet brush.

Use a plunger to create suction and force water down the drain.

This is the easiest and cheapest way to unclog a toilet. It can work and be successful in certain scenarios, but it also has its limitations: plunging only works when enough water can get through the blockage before it fills up to the top. A toilet plunger is just like a plunger you’d use for clogged drains.

If you try to plunge your toilet and it has already filled up completely, plunging will not work (usually). There is just too much water in the bowl for a plunger to create enough of the suction needed to break through a clog. A plunger can also get some pretty gross gunk all over it if you are trying to unblock a toilet with a clog that has already filled up once before.

Plunging can be helpful if you have water draining slowly from the overflow tube, or if you know the problem is not at the bottom of your toilet bowl. If plunging is used correctly and isn’t overused, it can help keep your toilet draining properly. But mostly, it should be used as a last resort. Plunging should only be done to clear a clog if there is a partial blockage, and your toilet bowl isn’t already completely full of water.

Run your bathtub’s hot water for a few minutes then pour it into the toilet bowl with some dish soap or other type of cleaner that is meant for clogs.

This is one of the most popular methods to clear clogs in toilets but it doesn’t always work. You can also mix some hot water and bleach together and pour that into your toilet bowl. The combination of both liquids may be capable of breaking down some clogs you have, however, this would only be used on very simple ones not involving paper.

The way you flush your toilet is very important because if your down the drain is a bit clogged then this can cause damage to your toilet and even result in it breaking. A good way to know which flush method is best for you when you are dealing with a clog would be to run water through the drains in your bathtub before using the toilet. This way you can figure out which flush method is best for your situation and avoid damage to either yourself or your property.

When washing clothes or doing dishes it is very important that if you hear a gurgling sound from your pipes then get someone to check them as they could be clogged and might need to be unclogged.

If you have a drain that is connected to the wall then it is important to make sure that when washing your hands in the sink or using other items that connect with the plumbing such as a hairdryer that you do not push down on the plug or handle. When they are pushed down hard enough, even for just an instant, it can cause the drain to clog and result in a very hard time trying to unclog them.

If you are trying to unclog your sink drain, it is important that you do not pour chemicals down it such as bleach. This can result in very severe damage to the pipes and then will require a lot of time and money to fix. A simple way to clear a clogged sink would be to fill it with boiling water and then run cold water down it after. This should be enough to clear the clog but if not then you can proceed with using chemicals.

If none of these methods work, call a professional plumber who can fix your problem!

Unclogging a toilet is pretty easy but sometimes there can be more serious issues that arise which may need to be dealt with by professionals. If your toilet has been clogged for several days and the above methods have not worked, then you should call someone who will be able to assess your plumbing situation and clear it without charging too much. It is not recommended to wait for too long before you seek help because a clogged toilet can cause permanent damage if left alone.

If you are having trouble with your plumbing or need some advice on how to fix something, ask us! We would be glad to assist you!

The post Common mistakes people make when learning how to unclog a toilet appeared first on Plumbing Company in Denver, CO.

Do you know what to look for when inspecting a home’s plumbing system?



It would be wise if you do, because it is an important factor in any potential purchase. Plumbing installation is not something that can be overlooked or taken lightly. It has the ability to make your new home feel like a comfortable and inviting place to live or it could result in disaster and misery. So before you invest in living space, read this article for helpful guidelines on how to inspect a property’s plumbing system so that you don’t end up regretting your decision later.

Inspect the water pressure.

This will help determine if there’s been any major water leaks that could have caused damage to the plumbing. You can check this by turning on all of the faucets in the home, including the water heater and washing machine. If you’ve noticed a change in pressure, most likely, there has been some sort of leak in its history.

Don’t just turn on the faucet, but run it for a brief moment then stop. Listen for any unusual sounds coming from the pipes. If you hear gurgling or trickling noises, something in your house could be ready to burst and cause damage to other important fixtures such as the tubs and sinks.

As much as possible, try to test the pressure when there aren’t any other people inside the home. This is because no one wants to find themselves standing with a shower head spewing water in their face!

If you can’t do the above, ask a friend to come over and turn on all of the faucets in the home while you stand outside or listen for any unusual sounds from inside.

Take note if there are any leaks around windows or doors. These could be places where pipes are loose and need to be replaced. You’ll want to make sure if you purchase the home that these leaks will be attended to before moving in.

Check for leaks or drips in the toilet.

If you’ve ever noticed that your toilet is constantly clogged with water, it may mean there’s a problem in the tank. To allow for proper flushing, both of its parts must have equal amounts of pressure–the tank and bowl. If they are not working together properly, then it could leave residue inside that may potentially grow mold.

If you also see the tank leaking, it’s best to contact a plumber right away because water could be seeping into walls or the home’s foundation and possibly causing further damage if not repaired in time.

Take note of any exposed pipes that you may come across while inspecting the plumbing system. These pipes should be wrapped in either a rag or plastic so that they don’t get damaged from coming into contact with the outside elements. If the pipes are exposed, there’s a good chance that they’re worn out, which will mean you’ll need to either repair or replace them later.

Look for visible signs of rust near any faucets and fixtures. If you notice it, chances are that there could be more somewhere else in the home. If you see rusty water coming out, then the pipes are most likely worn out and may cause serious problems if left unfixed.

Test all faucets, sinks, and toilets for proper function.

Inspect all faucets, sinks, and toilets to see if they’re still in good working order. If there are any that seem to be clogged or not functioning as well as they should, then you may want to get them repaired before moving on with the purchase of a property. This will save you from having to make an emergency call to a plumber once you’ve already moved in.

If your shower head is leaking, it may mean that there’s a crack somewhere in the pipe. But if there are no visible signs of damage to be seen, chances are, the problem is with a cartridge inside, in which case you’ll have to get someone out to repair it.

This is just a fraction of what you need to look out for before purchasing a home. Don’t be afraid to ask questions about the plumbing system from anyone who may know and if possible, get a second opinion from a plumber or someone else in the field. This way, you’ll have done everything within your power that will allow you to not have problems with your plumbing system in the near future.

Look in the basement to see if there are any signs of standing water or other issues with plumbing installation.

First check the basement for signs of standing water. This may not seem that important, but if you have a leak in your tank or elsewhere in your plumbing system, the excess water will end up here. Standing water is a sure sign that there is a problem with your plumbing installation. The most likely reason for this is condensation forming on your pipes, but you may have problems in your tank or other parts of the system.

No matter how hard you try to prevent them, plumbing issues will occur eventually. Most often this is due to a problem with your piping system, but it could also be due to a problem with your sink drain or clogged toilet. Pre-existing plumbing issues are probably one of the most important things to look for when buying a home. Fixing a plumbing problem in an older property can be costly and difficult.

There are two kinds of pipes you need to focus on: Pipes under the house and water supply lines leading into your house. The best place to check this is in the basement, but it’s also a good idea to check the pipes outside if you can.

With older properties there is always a chance that something may break under the house. This could be due to a variety of different reasons, but it’s something you should look for. Make sure there are no obvious signs of damage like cracks in walls and floors, as this may indicate that pipes have been broken or damaged and not repaired correctly.

If your water supply lines (the pipes leading from the street into your home) are broken or damaged you will see signs of this outside. Look for kinks in the piping, bulges, pits or other abnormal shapes in the piping itself. If you find a problem here it’s important to fix it as soon as possible; otherwise your water pressure could decrease over time and cause further damage throughout your home.

Inspect the sewer line to make sure it’s not damaged or cracked.

You may be able to see cracks on the outside of the pipe, but you’ll need a sewer camera inspection for an internal inspection. This is very important because damaged or cracked sewer lines can lead to expensive repairs and health hazards. While your inspector is in the process of inspecting your home’s plumbing system, he or she should take note if there are any signs of sewer line leaks. It’s advisable to hire a licensed plumber to check the sewer line every three years, and more often if there are issues.

An easier way for you to find out whether there is a problem with your home’s sewer lines is by hiring a certified inspector. These professionals will be able to give you advice on any necessary repairs. Near the end of the inspection, they will recommend whether you should contact a plumber to assess your sewer lines. If there appears to be leakage or damage in the line, you may want to get further treatment within two weeks before water damage sets it.

An open sewer pipe can cause your home’s foundation and walls to be soaked with waste water. If you hear gurgling sounds coming from the toilet, this could be a sign that there is an open drain pipe. It’s also advisable to check for excessive moisture in your basement or around exterior walls of your home. These are more signs of possible sewer line problems.

You can contact a plumbing company if you discover that there is a problem with your sewer lines. These professionals are licensed and certified to do repairs, replacements, inspections and remodeling in your home’s plumbing system. They should be able to fix your sewer line so that it doesn’t leak or rupture again.

***

If you’re planning on buying a home, it’s important to have the property inspected for plumbing issues before signing off on the purchase. A professional plumber can help identify potential problems and give homeowners peace of mind that they are making an informed decision when purchasing their new house.

With plumbing issues, the cost to repair can be more than what a homeowner might want to pay for during the inspection period; however, it’s important to know about any potential problems before signing on the dotted line.

The post Essential plumbing inspection points before you buy a home appeared first on Plumbing Company in Denver, CO.

Your sewer and drain system is one of the most important parts of your home. It’s what takes all the waste from you and your family, then transports it through pipes to a treatment plant or septic tank. Without it, everything would be piling up around your house! It’s important to keep it in peak condition.

How does sewer and drain cleaning work?

Sewer and drain cleaning is a specialized field involving many different methods used to clean the pipelines that run your plumbing. The ways in which it works vary depending upon what exactly needs to be cleaned out, how long the buildup has been occurring, and other factors. The method that is used will depend on circumstances, but there are certain general truths about how sewer cleaning works.

So just how does it work? There are three main methods in which the process of sewage and drain cleaning takes place: mechanical, chemical, and hydro-jetting.

If you have a simple clog to clear out or if there is a simple break in the pipe that needs to be cleared, your plumber may just use a mechanical tool. Mechanical tools include things like drain snakes and cable tools. Drain snakes are inserted through the drain into the pipes and they will grab onto any hair or other obstructions. They are then pulled out of the pipes so that all of the debris can be easily wiped away. Cable tools are similar to drain snakes but they have a thin wire attached to the front which is used to try and grab onto an obstruction that needs clearing out of the pipes. Cable tools will usually need to go through several cycles before there is no more resistance from the obstruction because they can only pull out one piece at a time.

If there is a larger clog that needs to be cleared or the blockage is out of reach, chemicals will often be used. Chemical drain cleaners are usually activated by water and they work their way through the pipes to break down any buildup or clogs that may be present. The chemicals can also dissolve things like mineral deposits from hard water in pipes, keeping the pipes running smoothly. After the chemical has done its work it will usually be washed away by water. It is important to follow all of the instructions on any chemicals that you choose for cleaning your drains and pipes, since improper use can lead to harmful results.

Using hydro-jetters involves forcing high pressure water through a hose into the pipes. The water stream will be strong enough to break up any buildup that may be present in the pipelines and the debris will be washed away by a vacuum. This is one of the more effective methods for dealing with stubborn clogs or problems within your plumbing system because it can get so deep into the system, but this method requires very specialized equipment.

What are the causes of sewer and drain blockages?

When it comes to drains and sewers, there are plenty of things that can cause a blockage. From cooking oils and grease entering the system to debris simply collecting in the pipes over time, these blockages will end up with you calling for services. But there is one thing in particular that many know little about; tree roots causing damage to the drains and sewers.

Tree roots are one of the main causes of sewer and drain blockages, as they grow into and through pipes that mark their location on both private properties and public roads. Tree roots will naturally seek out water, so it is not uncommon for large trees to become a home for these blocks over time. Therefore, it is important to have these roots removed by a professional.

Using root-killing chemical products from the local shop will do little to combat this problem, as they are designed for regular garden use and not commercial use. It’s best that you stick with professional help rather than attempting to fix the problem yourself. Root removal should be done often, as it will make the process easier for you and your customers.

Why is it important to get your drains cleaned regularly?

There are many reasons why you need to get your drains cleaned regularly, especially if there’s an issue with it. The first reason is that drain cleaning will solve a problem in the present. You don’t want a flood of water coming through your walls or a horrendous smell taking over your home. It will also prevent further damage from being done to the plumbing. It will also prevent it from getting worse, like mold and mildew growing in your walls because of stagnant water.

Drain cleaning is also a prevention as well. If you let a clogged drain go for too long, you may end up with a large bill from your plumber or the city sewer board if it’s a main drain. Regular maintenance can keep the drain flowing smoothly and save you money in the future.

Risks of neglecting your drains:

1) The toilet might occasionally clog up due to grease or other non-solid objects going down it. This is easily avoided by using a garbage disposal.

2) If the sink gets clogged up from being used too much and grease or other solid objects going down the drain, you may have to replace a P-trap.

3) Drain cleaning is often quoted at around $500 by plumbers when it comes to clearing clogs. If left unchecked for months, your house could end up reeking of sewage or mold and mildew.

4) If the drain is not functioning properly, water might occasionally start pouring into your basement and flooding it.

5) This should be mentioned mostly for homes with basements or crawl spaces. If a main drain line gets clogged up from grease or any other solid object in the pipe, it will overflow out of your walls and the sewage or other garbage will end up in your basement.

6) If you don’t have a clog but can smell a foul odor, check to make sure there is no sewage backing up into your house. 

Tips for preventing clogs in the future

If you have a pipe which is accustomed to clogging, it is essential that you get the issue solved as early as possible. Clogs can be caused by an abundance of things such as tree roots, hair, grease and paper products. It is not always necessary for these items to remain in the pipes because they can be removed with the help of a plumber.

They can be scraped off or sliced, depending on the material they are made out of. Tree roots are drawn to water and not all of them will inevitably reach your sewer line. You may find that the opening is plugged from time to time due to these tree roots and you must have it cleaned out when this happens.

In case a drain in your house is clogged, you should not try to remedy the problem on your own. It is advised that you call in an emergency plumber like everyone else because of the potential risk involved. The most common way people attempt to fix such problems is by using chemical cleaners or pouring hot water down the sink. You must understand that this can cause damage to the piping under your home and it is not worth taking such a chance.

If you are wondering about what produces clogs in a pipe, tissue paper might be one of them. Toilet paper disintegrates in water which means it will ultimately end up inside the drain or even outside in the pipes where more problems may occur. It is best to use a garbage disposal for this purpose and avoid using soap or detergents which can backfire in case they are mixed with the toilet paper.

The post What You Should Know When It Comes To Sewer and Drain Cleaning appeared first on Plumbing Company in Denver, CO.