You may be wondering why the water in the toilet bowl won’t go down or has been slowing down and backing up. You might have tried plunging it with no luck. This blog post will show you a few different methods to unclog a toilet when all else fails. If one doesn’t work, try another until you find one that does! With patience and persistence, there’s hope for your problem yet!

Plunging the toilet won’t work

Plunging is one of the most common methods people try when they’re having a slow draining toilet. Using a plunger works because it creates suction to help push the water down the drain and break up any clogs that are in your pipes. If you don’t have success with this method after trying it a few times, it’s best to try other options. Let’s say you have a slow draining toilet and decide to plunge it, but the plunger doesn’t work; what do you do? You can buy a toilet auger that will help remove blockages from your pipes. This tool is shaped like an old-fashioned corkscrew, so it’s basically a plunger on a wire.

Don’t use harsh chemicals, especially if you have a septic tank.

Harsh chemicals can damage your toilet, your septic system, and it could even cause a bigger clog. They can remove the finish from your toilet bowl if you’re not careful when using them. It’s best to use milder or natural solutions first unless you know of no other options. If they don’t work, then try a harsher solution. Be careful when using these chemicals to unclog a toilet. If you’re not sure about what you’re doing, hire a professional to help you out.

Sea salt, baking soda, and vinegar are all great ways to unclog a toilet. Fill the bowl with one of these ingredients and swish it around with a toilet brush. Make sure you use enough until it covers the sides as well as the bottom of the toilet bowl. The natural acids in the vinegar will help dissolve grime build-up. Salt has the same effect, but it also helps to dissolve water deposits and mineral scales that can slow down your toilet. Just be careful with these methods because they won’t damage the inner workings of a toilet or septic tank like chemical solutions will.

Treat your toilet like a garden. Sometimes, the problem could be that you’re not keeping your toilet bowl clean enough. Over time, things such as hair and food particles can build up in there. You don’t want to remove everything from it every time you go to the bathroom, but you should make sure it’s looked over once a week. Look for things like limescale deposits and grime build-up to see if you need to scrub it out with a toilet brush.

Clean your toilet more frequently. If you have a septic tank, then it helps if you can keep the bowl clean by cleaning it at least once every 2 weeks. That way, things like hair and food won’t build up in there as much. Make sure that when you’re putting materials inside the toilet bowl, they don’t get stuck.

If you have a slow-running toilet, then it’s probably because the flapper is broken. This is a plastic piece that hangs over the opening of your toilet tank and seals it when you flush it. If this part broke or fell off, then the water will pretty much run non-stop until someone fixes it. Replace the flapper by taking off the tank lid and then unscrewing it from inside. You can purchase a new flapper at any home improvement store.

Cleaning your toilet bowl with vinegar once a month is a good way to keep limescale deposits from building up. It also helps to prevent rust and mineral buildup, as well as character build-up and grime. Make sure you pour enough in there to cover the bottom and sides of your bowl, then scrub it down with a toilet brush.

Use a plunger to create suction and force water down the drain.

This is the easiest and cheapest way to unclog a toilet. It can work and be successful in certain scenarios, but it also has its limitations: plunging only works when enough water can get through the blockage before it fills up to the top. A toilet plunger is just like a plunger you’d use for clogged drains.

If you try to plunge your toilet and it has already filled up completely, plunging will not work (usually). There is just too much water in the bowl for a plunger to create enough of the suction needed to break through a clog. A plunger can also get some pretty gross gunk all over it if you are trying to unblock a toilet with a clog that has already filled up once before.

Plunging can be helpful if you have water draining slowly from the overflow tube, or if you know the problem is not at the bottom of your toilet bowl. If plunging is used correctly and isn’t overused, it can help keep your toilet draining properly. But mostly, it should be used as a last resort. Plunging should only be done to clear a clog if there is a partial blockage, and your toilet bowl isn’t already completely full of water.

Run your bathtub’s hot water for a few minutes then pour it into the toilet bowl with some dish soap or other type of cleaner that is meant for clogs.

This is one of the most popular methods to clear clogs in toilets but it doesn’t always work. You can also mix some hot water and bleach together and pour that into your toilet bowl. The combination of both liquids may be capable of breaking down some clogs you have, however, this would only be used on very simple ones not involving paper.

The way you flush your toilet is very important because if your down the drain is a bit clogged then this can cause damage to your toilet and even result in it breaking. A good way to know which flush method is best for you when you are dealing with a clog would be to run water through the drains in your bathtub before using the toilet. This way you can figure out which flush method is best for your situation and avoid damage to either yourself or your property.

When washing clothes or doing dishes it is very important that if you hear a gurgling sound from your pipes then get someone to check them as they could be clogged and might need to be unclogged.

If you have a drain that is connected to the wall then it is important to make sure that when washing your hands in the sink or using other items that connect with the plumbing such as a hairdryer that you do not push down on the plug or handle. When they are pushed down hard enough, even for just an instant, it can cause the drain to clog and result in a very hard time trying to unclog them.

If you are trying to unclog your sink drain, it is important that you do not pour chemicals down it such as bleach. This can result in very severe damage to the pipes and then will require a lot of time and money to fix. A simple way to clear a clogged sink would be to fill it with boiling water and then run cold water down it after. This should be enough to clear the clog but if not then you can proceed with using chemicals.

If none of these methods work, call a professional plumber who can fix your problem!

Unclogging a toilet is pretty easy but sometimes there can be more serious issues that arise which may need to be dealt with by professionals. If your toilet has been clogged for several days and the above methods have not worked, then you should call someone who will be able to assess your plumbing situation and clear it without charging too much. It is not recommended to wait for too long before you seek help because a clogged toilet can cause permanent damage if left alone.

If you are having trouble with your plumbing or need some advice on how to fix something, ask us! We would be glad to assist you!

The post Common mistakes people make when learning how to unclog a toilet appeared first on Plumbing Company in Denver, CO.

Do you know what to look for when inspecting a home’s plumbing system?



It would be wise if you do, because it is an important factor in any potential purchase. Plumbing installation is not something that can be overlooked or taken lightly. It has the ability to make your new home feel like a comfortable and inviting place to live or it could result in disaster and misery. So before you invest in living space, read this article for helpful guidelines on how to inspect a property’s plumbing system so that you don’t end up regretting your decision later.

Inspect the water pressure.

This will help determine if there’s been any major water leaks that could have caused damage to the plumbing. You can check this by turning on all of the faucets in the home, including the water heater and washing machine. If you’ve noticed a change in pressure, most likely, there has been some sort of leak in its history.

Don’t just turn on the faucet, but run it for a brief moment then stop. Listen for any unusual sounds coming from the pipes. If you hear gurgling or trickling noises, something in your house could be ready to burst and cause damage to other important fixtures such as the tubs and sinks.

As much as possible, try to test the pressure when there aren’t any other people inside the home. This is because no one wants to find themselves standing with a shower head spewing water in their face!

If you can’t do the above, ask a friend to come over and turn on all of the faucets in the home while you stand outside or listen for any unusual sounds from inside.

Take note if there are any leaks around windows or doors. These could be places where pipes are loose and need to be replaced. You’ll want to make sure if you purchase the home that these leaks will be attended to before moving in.

Check for leaks or drips in the toilet.

If you’ve ever noticed that your toilet is constantly clogged with water, it may mean there’s a problem in the tank. To allow for proper flushing, both of its parts must have equal amounts of pressure–the tank and bowl. If they are not working together properly, then it could leave residue inside that may potentially grow mold.

If you also see the tank leaking, it’s best to contact a plumber right away because water could be seeping into walls or the home’s foundation and possibly causing further damage if not repaired in time.

Take note of any exposed pipes that you may come across while inspecting the plumbing system. These pipes should be wrapped in either a rag or plastic so that they don’t get damaged from coming into contact with the outside elements. If the pipes are exposed, there’s a good chance that they’re worn out, which will mean you’ll need to either repair or replace them later.

Look for visible signs of rust near any faucets and fixtures. If you notice it, chances are that there could be more somewhere else in the home. If you see rusty water coming out, then the pipes are most likely worn out and may cause serious problems if left unfixed.

Test all faucets, sinks, and toilets for proper function.

Inspect all faucets, sinks, and toilets to see if they’re still in good working order. If there are any that seem to be clogged or not functioning as well as they should, then you may want to get them repaired before moving on with the purchase of a property. This will save you from having to make an emergency call to a plumber once you’ve already moved in.

If your shower head is leaking, it may mean that there’s a crack somewhere in the pipe. But if there are no visible signs of damage to be seen, chances are, the problem is with a cartridge inside, in which case you’ll have to get someone out to repair it.

This is just a fraction of what you need to look out for before purchasing a home. Don’t be afraid to ask questions about the plumbing system from anyone who may know and if possible, get a second opinion from a plumber or someone else in the field. This way, you’ll have done everything within your power that will allow you to not have problems with your plumbing system in the near future.

Look in the basement to see if there are any signs of standing water or other issues with plumbing installation.

First check the basement for signs of standing water. This may not seem that important, but if you have a leak in your tank or elsewhere in your plumbing system, the excess water will end up here. Standing water is a sure sign that there is a problem with your plumbing installation. The most likely reason for this is condensation forming on your pipes, but you may have problems in your tank or other parts of the system.

No matter how hard you try to prevent them, plumbing issues will occur eventually. Most often this is due to a problem with your piping system, but it could also be due to a problem with your sink drain or clogged toilet. Pre-existing plumbing issues are probably one of the most important things to look for when buying a home. Fixing a plumbing problem in an older property can be costly and difficult.

There are two kinds of pipes you need to focus on: Pipes under the house and water supply lines leading into your house. The best place to check this is in the basement, but it’s also a good idea to check the pipes outside if you can.

With older properties there is always a chance that something may break under the house. This could be due to a variety of different reasons, but it’s something you should look for. Make sure there are no obvious signs of damage like cracks in walls and floors, as this may indicate that pipes have been broken or damaged and not repaired correctly.

If your water supply lines (the pipes leading from the street into your home) are broken or damaged you will see signs of this outside. Look for kinks in the piping, bulges, pits or other abnormal shapes in the piping itself. If you find a problem here it’s important to fix it as soon as possible; otherwise your water pressure could decrease over time and cause further damage throughout your home.

Inspect the sewer line to make sure it’s not damaged or cracked.

You may be able to see cracks on the outside of the pipe, but you’ll need a sewer camera inspection for an internal inspection. This is very important because damaged or cracked sewer lines can lead to expensive repairs and health hazards. While your inspector is in the process of inspecting your home’s plumbing system, he or she should take note if there are any signs of sewer line leaks. It’s advisable to hire a licensed plumber to check the sewer line every three years, and more often if there are issues.

An easier way for you to find out whether there is a problem with your home’s sewer lines is by hiring a certified inspector. These professionals will be able to give you advice on any necessary repairs. Near the end of the inspection, they will recommend whether you should contact a plumber to assess your sewer lines. If there appears to be leakage or damage in the line, you may want to get further treatment within two weeks before water damage sets it.

An open sewer pipe can cause your home’s foundation and walls to be soaked with waste water. If you hear gurgling sounds coming from the toilet, this could be a sign that there is an open drain pipe. It’s also advisable to check for excessive moisture in your basement or around exterior walls of your home. These are more signs of possible sewer line problems.

You can contact a plumbing company if you discover that there is a problem with your sewer lines. These professionals are licensed and certified to do repairs, replacements, inspections and remodeling in your home’s plumbing system. They should be able to fix your sewer line so that it doesn’t leak or rupture again.

***

If you’re planning on buying a home, it’s important to have the property inspected for plumbing issues before signing off on the purchase. A professional plumber can help identify potential problems and give homeowners peace of mind that they are making an informed decision when purchasing their new house.

With plumbing issues, the cost to repair can be more than what a homeowner might want to pay for during the inspection period; however, it’s important to know about any potential problems before signing on the dotted line.

The post Essential plumbing inspection points before you buy a home appeared first on Plumbing Company in Denver, CO.

Your sewer and drain system is one of the most important parts of your home. It’s what takes all the waste from you and your family, then transports it through pipes to a treatment plant or septic tank. Without it, everything would be piling up around your house! It’s important to keep it in peak condition.

How does sewer and drain cleaning work?

Sewer and drain cleaning is a specialized field involving many different methods used to clean the pipelines that run your plumbing. The ways in which it works vary depending upon what exactly needs to be cleaned out, how long the buildup has been occurring, and other factors. The method that is used will depend on circumstances, but there are certain general truths about how sewer cleaning works.

So just how does it work? There are three main methods in which the process of sewage and drain cleaning takes place: mechanical, chemical, and hydro-jetting.

If you have a simple clog to clear out or if there is a simple break in the pipe that needs to be cleared, your plumber may just use a mechanical tool. Mechanical tools include things like drain snakes and cable tools. Drain snakes are inserted through the drain into the pipes and they will grab onto any hair or other obstructions. They are then pulled out of the pipes so that all of the debris can be easily wiped away. Cable tools are similar to drain snakes but they have a thin wire attached to the front which is used to try and grab onto an obstruction that needs clearing out of the pipes. Cable tools will usually need to go through several cycles before there is no more resistance from the obstruction because they can only pull out one piece at a time.

If there is a larger clog that needs to be cleared or the blockage is out of reach, chemicals will often be used. Chemical drain cleaners are usually activated by water and they work their way through the pipes to break down any buildup or clogs that may be present. The chemicals can also dissolve things like mineral deposits from hard water in pipes, keeping the pipes running smoothly. After the chemical has done its work it will usually be washed away by water. It is important to follow all of the instructions on any chemicals that you choose for cleaning your drains and pipes, since improper use can lead to harmful results.

Using hydro-jetters involves forcing high pressure water through a hose into the pipes. The water stream will be strong enough to break up any buildup that may be present in the pipelines and the debris will be washed away by a vacuum. This is one of the more effective methods for dealing with stubborn clogs or problems within your plumbing system because it can get so deep into the system, but this method requires very specialized equipment.

What are the causes of sewer and drain blockages?

When it comes to drains and sewers, there are plenty of things that can cause a blockage. From cooking oils and grease entering the system to debris simply collecting in the pipes over time, these blockages will end up with you calling for services. But there is one thing in particular that many know little about; tree roots causing damage to the drains and sewers.

Tree roots are one of the main causes of sewer and drain blockages, as they grow into and through pipes that mark their location on both private properties and public roads. Tree roots will naturally seek out water, so it is not uncommon for large trees to become a home for these blocks over time. Therefore, it is important to have these roots removed by a professional.

Using root-killing chemical products from the local shop will do little to combat this problem, as they are designed for regular garden use and not commercial use. It’s best that you stick with professional help rather than attempting to fix the problem yourself. Root removal should be done often, as it will make the process easier for you and your customers.

Why is it important to get your drains cleaned regularly?

There are many reasons why you need to get your drains cleaned regularly, especially if there’s an issue with it. The first reason is that drain cleaning will solve a problem in the present. You don’t want a flood of water coming through your walls or a horrendous smell taking over your home. It will also prevent further damage from being done to the plumbing. It will also prevent it from getting worse, like mold and mildew growing in your walls because of stagnant water.

Drain cleaning is also a prevention as well. If you let a clogged drain go for too long, you may end up with a large bill from your plumber or the city sewer board if it’s a main drain. Regular maintenance can keep the drain flowing smoothly and save you money in the future.

Risks of neglecting your drains:

1) The toilet might occasionally clog up due to grease or other non-solid objects going down it. This is easily avoided by using a garbage disposal.

2) If the sink gets clogged up from being used too much and grease or other solid objects going down the drain, you may have to replace a P-trap.

3) Drain cleaning is often quoted at around $500 by plumbers when it comes to clearing clogs. If left unchecked for months, your house could end up reeking of sewage or mold and mildew.

4) If the drain is not functioning properly, water might occasionally start pouring into your basement and flooding it.

5) This should be mentioned mostly for homes with basements or crawl spaces. If a main drain line gets clogged up from grease or any other solid object in the pipe, it will overflow out of your walls and the sewage or other garbage will end up in your basement.

6) If you don’t have a clog but can smell a foul odor, check to make sure there is no sewage backing up into your house. 

Tips for preventing clogs in the future

If you have a pipe which is accustomed to clogging, it is essential that you get the issue solved as early as possible. Clogs can be caused by an abundance of things such as tree roots, hair, grease and paper products. It is not always necessary for these items to remain in the pipes because they can be removed with the help of a plumber.

They can be scraped off or sliced, depending on the material they are made out of. Tree roots are drawn to water and not all of them will inevitably reach your sewer line. You may find that the opening is plugged from time to time due to these tree roots and you must have it cleaned out when this happens.

In case a drain in your house is clogged, you should not try to remedy the problem on your own. It is advised that you call in an emergency plumber like everyone else because of the potential risk involved. The most common way people attempt to fix such problems is by using chemical cleaners or pouring hot water down the sink. You must understand that this can cause damage to the piping under your home and it is not worth taking such a chance.

If you are wondering about what produces clogs in a pipe, tissue paper might be one of them. Toilet paper disintegrates in water which means it will ultimately end up inside the drain or even outside in the pipes where more problems may occur. It is best to use a garbage disposal for this purpose and avoid using soap or detergents which can backfire in case they are mixed with the toilet paper.

The post What You Should Know When It Comes To Sewer and Drain Cleaning appeared first on Plumbing Company in Denver, CO.

A lot of people don’t know this, but flushing your toilet doesn’t really clean it. After you flush, the water that’s in your toilet bowl swirls around and creates a vortex. The dirty water is pushed up against the sides of the bowl, so when you flush again all that dirt gets swept away with the freshwater.

1. 1. Flushing your toilet doesn’t really clean it

2. What does clean a toilet?

3. Why we need to clean our toilets regularly

4. The things that might make your toilet dirty 

5. How to properly care for a dirty or clogged toilet without using harsh chemicals

Flushing your toilet doesn’t really clean it

The toilet is one of the dirtiest places in your house. But what you might not have realized is that flushing your toilet doesn’t really clean it, because all of the dirty water in your bowl swirls around and creates a vortex. The dirty water gets pushed up against the sides of the bowl so when you flush again all that dirt goes with it- along with whatever freshwater was supposed to be cleaning things!



That’s why we need to clean our toilets regularly- especially if other people are using them or there’s been another reason for extra messiness like sickness.

It’s a dirty job, but somebody has to do it. Cleaning toilets is a necessity for the health and safety of our homes. Not only will you be protecting your family from life-threatening diseases like E Coli, but you’ll also be saving on water usage and reducing your carbon footprint by using less toilet paper and soap.

A clean toilet prevents the growth of bacteria (lovely, right?)- and it can even save you money by preventing clogs from forming in your pipes!

What does clean a toilet?

Ever wonder what you’re supposed to use to clean a toilet? Well, you might be surprised. You can use some regular household items that are just as effective at cleaning your toilet as the chemicals or cleaners from the store!

In order to keep things simple and prevent any unnecessary messes, we recommend using baking soda and white vinegar. All you have to do is pour them into the bowl along with water, scrub gently around with a non-abrasive sponge until everything looks nice and sparkly again, then flush away for instant freshness!

There are many different opinions on the subject of how to keep your loo sparkling. Some people say to use bleach, but the fumes can be toxic and it’s not safe for you or your family!

Others suggest using vinegar because of its natural cleaning power, which is great if there are young children around who might accidentally drink some (it tastes awful!).

Some folks think that dish soap does just as good a job at keeping things clean so we recommend giving it a try too.

For those with sensitive skin or noses, baking soda alone may do the trick without any added chemicals. Just mix in some water and scrub away! You’ll have a clean toilet bowl in no time flat with nothing more than basic household products on hand.

A Plumbing Installation Company is a great place to call for help with cleaning your toilet. Your plumber will have the tools and knowledge necessary to get your toilet sparkling clean. Not only can they provide you with all of the supplies that you need, but they also offer professional advice on how to keep it looking nice in the future.

Why we need to clean our toilets regularly

The toilet is one of the dirtiest places in your house. It’s the place where you relieve yourself and it doesn’t get cleaned often, so bacteria starts to grow. You need to clean your toilet every day! By doing this, you’re preventing illness from spreading around your household. Cleaning your toilet will make a world of difference in how good everything smells; it also helps keep down mold and mildew growth which can be harmful to people with asthma or allergies. 

I’m sure many of us have been in a situation where our toilets are so dirty that we avoid using them at all costs, even if that means going out of our way just to use the bathroom somewhere else. In order to remedy this issue, we need an expert plumber from a plumbing installation company who can give our toilets regular attention with deep cleaning every few months as well as repairs on any issues that come up such as broken flappers or running water from the tank into the bowl when flushed.

A dirty toilet can be a breeding ground for bacteria, which is why it’s so important to have your toilets regularly cleaned. This will keep harmful substances away from the inside of your home and also make you feel better about using them because they’ll go down much more smoothly without all that grime sticking to the sides of the bowl.

Plumbing installation company services include regular maintenance on plumbing lines as well as repairs on issues such as running water or clogged drains in order to ensure no one has an issue with their plumbing during emergencies. Plumbers are always prepared!

The things that might make your toilet dirty

It is a fact that your toilet can be dirty, and it may not even be something you are aware of. There are many things that could make the inside of your toilet dirty, such as urine, feces, bacteria, or mold. If left alone for too long these things can cause an unpleasant smell to form in the bathroom and even lead to illness so it is important to know what might make your toilet dirty and how you can prevent this from happening. 

It’s an unavoidable space because of the simple fact that we all have to use it. While it is unavoidable, there are things that can be done to keep the space clean and sanitary. One of these steps would be simply flushing your toilet after use in order to remove anything created by this process but sometimes even just a flush isn’t enough!

A few ways you could make your toilet dirty if left alone for too long: Urine is one thing that may get in contact with the inside of your toilet because we all have to urinate at some point when using a restroom. This leaves behind bacteria on the surface of your bowl and can cause an unpleasant smell or lead to illness. Feces are another common culprit and create a much more intense odor whereas urine does not more than being an annoyance.

Other things that can happen with a dirty toilet are leaks and clogs which may cause damage to your flooring or even result in raw sewage backing up into the room if you’re unlucky enough for it to backup all the way from the sewer line!

The plumbing installation company will come out, assess what needs to be done, and then implement any necessary repairs. This could include anything from fixing leaky pipes to replacing broken parts such as flappers so make sure not to wait until there is a problem before restoring cleanliness!

If we use our toilets improperly they will become dirty which leads to potential health risks. The next time you go into the bathroom think about what might have been touching your toilet seat before you sat down on it. Think about how easy it is to touch your mouth, nose, or skin before using the toilet as well. There are many things people do not think of that can make their toilets dirty and become a health hazard for themselves and others who use them afterward.

How to properly care for a dirty or clogged toilet without using harsh chemicals

The toilet is one of the most commonly used appliances in your home and, as such, it can get very dirty – but don’t worry! There are a few easy ways to care for your toilet without using harsh chemicals.

There are many harsh chemical cleaners on the market but they may come with harmful side effects. They can also cause damage to your toilets if you use them too often. For example, bleach is toxic and chlorine corrodes metal parts in the toilet. There are far safer ways of cleaning a dirty or clogged toilet without resorting to harsh chemicals:

• -To clean the outside of your toilet, all you need is some vinegar diluted with water – two cups for every one cup of vinegar will do nicely! Get a sponge or rag that does not have any printing on it (to avoid damaging your sealant) and wipe away dirt from hard surfaces.
• – Avoid using abrasive cleaners like Comet because they remove protective coatings present on most porcelain materials which could lead to leaks over time. Use something safe like baking soda instead.
• – Toilet brushes are for scrubbing and not actually cleaning. Use a toilet brush to remove any stubborn grime from the inside of your bowl, then flush with water only if necessary. If you have hard water or lime build-up problems, this is a good time to add some bleach (or another cleaner) into the mix before rinsing again since they can dissolve mineral deposits in plumbing systems better than just soap alone.

Harsh chemicals are not required to clean your toilet. A plumbing installation company can help you out with this task without the use of harsh chemicals and they will know just what to do. There is a lot more than a plumbing company does than just fixing toilets, so don’t hesitate to call them if you need anything from an installation, repair, or any other kind of service they offer.

The post When Just Flushing Your Toilet Isn’t Enough appeared first on Plumbing Company in Denver, CO.

One of the best ways to maintain your dishwasher is by hiring a professional plumbing installation company to do routine maintenance. It is important that you periodically run a test on your dishwasher to make sure it’s working properly before every use. Dishwashers are known for being water-consumers, which can lead to excessive usage of both water and energy bills if not adequately maintained. For this reason, it is wise to hire a plumber or repairman from time to time so as not to be faced with an expensive bill down the road due to negligence in upkeep.

1. Why dishwashers are important

2. What to do if your dishwasher is not draining properly

3. Tips for preventing clogs in the drain of your dishwasher

4. How to get rid of hard water stains on dishes and on the inside of your dishwasher 

5. Ways to keep food from sticking to dishes and how you can prevent it 

6. Tips for washing delicate items like silverware, glassware, or fine china that needs hand-washing

Why dishwashers are important

Dishwashers are a necessity for any family. Without one, you would have to hand wash all of the dishes and pots that your family uses while cooking dinner. This is an arduous task that takes up a lot of time. With dishwashers, you can quickly get them squeaky clean with just the push of a button! 

Dishwasher detergent also makes it easier because you don’t have to scrub every single dish by hand. It’s actually quite enjoyable for kids to help out and they’ll be excited when their hands aren’t covered in suds anymore! Nowadays, most homes come equipped with at least one dishwasher which will save everyone so much time on an everyday chore like washing dishes – what could be better?

However, it’s important to keep up with dishwasher maintenance. Dishwashers are machines that can break down and malfunction if they’re not cared for properly. For example, you should make sure the dishwasher is running on a low water level so as to prevent flooding in your kitchen or basement – also check the filter regularly to ensure nothing is clogging the drain.

A dirty dishwasher will also cause a buildup of bacteria and mold, so be sure to clean out your dishwasher monthly with vinegar – this is an easy do-it-yourself project that can help stop potential health hazards in their tracks! Dishwashers are great for households both big and small because they make washing dishes a much quicker and easier task.

If you have any questions about dishwasher maintenance, we’re always happy to answer your call!

Dishwashers are machines that can break down if not cared for properly. Dishwashers clean dishes quickly and easily – but with some simple care, they’ll last longer! If you need help maintaining your dishwasher, we’re always happy to help – just give us a call!

What to do if your dishwasher is not draining properly

A common issue with dishwashers is that they don’t drain properly. Dishwasher drainage problems can be caused by a clog in the hose, a blockage or an obstruction in the pump filter screen, and other reasons. Depending on what’s causing your dishwasher to not drain properly, there are many different solutions you can use to fix this problem. 

What can you do if your dishwasher is not draining properly? This may seem like a daunting question, but there are a few simple things that you can check before calling the plumber. The first thing to do is unplug the dishwasher, and then use a flashlight to look in the drain hole. If there is debris or food caught in the drain, it’s time for an old-fashioned plunger.

Take some hot water with soap added and put it into the sink so that it covers most of its surface area. Have someone hold down on top of the plunger while you push up and down several times until all of the air bubbles stop coming out. You should be able to see what was clogging your dishwasher by now the water. If it seems like there’s an object that is not easily removed, try pouring a kettle of boiling hot water into the sink to loosen and break up whatever has been clogging your dishwasher drain.



After you’ve cleared out whatever was in the dishwasher catch basin, unplug it again and run some freshwater through one more time before trying to use the machine again – this will remove any residual soap or grime that may remain from when you were using the plunger. Now you’re ready to get back to cooking with clean dishes!

Tips for preventing clogs in the drain of your dishwasher

If you are having trouble with clogs in your dishwasher, it might be time to give the inside of the machine a good scrub. You can do this by removing all dishes and utensils from the dishwasher, so you have easy access to reach every area. Use a dishwashing soap that is specially formulated for cleaning appliance surfaces.

If some items are stuck on tightly, try soaking them in warm water before giving them an extra scrub with a sponge or cloth dipped in soap solution. Scrub until you see no more residue. Rinse everything well and dry completely before putting back into place inside your machine. Make sure there is nothing left behind as this could cause future clogs problems.



Many people don’t know that the drain of a dishwasher is actually designed to clog. This is because the water in your dishwasher needs somewhere to go when it’s not being used, and if it doesn’t have anywhere to go, then you’ll end up with a flooded kitchen floor.

How to get rid of hard water stains on dishes and on the inside of your dishwasher

If you’re tired of looking at those hard water stains on your dishes, it’s time to take action! There are a few different ways that will work in getting rid of them. First, try soaking the dish in vinegar for an hour or two and then scrubbing it with baking soda. You can also pour white distilled vinegar over the stain and let it soak for about 30 minutes before rinsing off with warm water.

Lastly, if you have a really stubborn stain on something like glassware or silverware, try boiling some apple cider vinegar in a pot until it reduces to one cup and add ¼ teaspoon of salt to help remove residue from these items when they cool down. Rinse thoroughly after using any technique mentioned above- most of the time these stains are left behind after washing dishes because they were not properly wiped or rinsed.

Ways to keep food from sticking to dishes and how you can prevent it

It is a common problem for food to stick to dishes and it can be frustrating. There are ways you can prevent this from happening though, such as by using cooking spray or oil. You could also try adding some powdered sugar or cornstarch when making your sauce so the liquid will coat the food better.

Everyone has their own tricks that they use in order to combat sticking but there are other reasons why this may happen too such as because of how you prepared the dish itself or if you have an old dishwasher due to years of neglect which will not clean well anymore and needs replacing with a new model.

There are many reasons why food may stick to dishes, such as how you prepared the dish or if your old dishwasher needs replacing. It’s important to keep all parts of your dishwashing machine clean in order for it to work at its best and last longer. With proper maintenance, a well-maintained machine will not only function better but also increase its lifespan considerably.

Tips for washing delicate items like silverware, glassware, or fine china that needs hand-washing

Washing delicate items is a task that many people dread, but there are some simple steps you can take to make the process easier most, make sure you have the right detergent for the job. Many dishwasher powders are not safe to use on delicate items so be certain that your choice is labeled as such or it will scratch up any dishes and pots used in their manufacture.

When washing fine china cups with a dishwasher full of water, leave them out at room temperature until they dry completely before putting them back into cupboards. This process helps prevent moisture from collecting inside these fragile pieces.

When hand-washing glassware always remember to rinse thoroughly under running tap water.

With proper maintenance, a well-maintained machine will increase its lifespan considerably due to years of neglect which will not clean well anymore.

First and foremost, always start by filling your sink with warm water before adding any soap or detergent! This will help avoid chipping as well as provide for more lubrication when scrubbing at stubborn stains.

Next, use a gentle non-abrasive sponge instead of a dish brush to clean both sides of every item in the set.

Finally, never leave dishes soaking until they’re needed again – this may lead to mineral deposits on surfaces which could cause staining over time! Remember these tips next time you need to wash fine glassware or silverware because we all know how much they can make a mess.

The post The Importance of Dishwasher Maintenance appeared first on Plumbing Company in Denver, CO.

When you’re looking to get a new water heater system, the first thing you should do is learn as much as you can about the different types of heaters so that you can choose the right one. Generally, there are two types of heating units: the tank and tankless variations. These different types have different benefits and downsides, which is why it’s important that you are able to choose one that suits your needs.
That said, here is our guide on how to choose between the tank and tankless variations:

How Much Does a Water Heater Cost?

Before we can go into detail about the tank and tankless water heaters, you need to know how much a typical unit costs. You can find a decent water heater that can handle your day-to-day needs for around $1,000. However, you should keep in mind that such heaters are on the lower end of the spectrum, as decent ones can go for much higher prices. The most balanced options for residential use generally cost around $2,500 to $3,000, so you shouldn’t always go for the cheapest option.

How Long Does a Water Heater Last?

A proper-sized water heater can last up to 20 years with adequate care, but the models that can last that long without becoming highly inefficient are incredibly rare. You can realistically expect a model to last for around 6 to 12 years before it needs to be changed, so keep that in mind when you’re buying a water heater.

How Much Does It Cost to Install a Water Heater?

The installation cost is usually more static than the price of the heater itself, as there aren’t that many factors that can make it vary too much. For a standard 50-gallon heater, you can expect to pay around $1,200 to have it installed. That price can turn out to be cheaper or more expensive, depending on the service charge, expertise, and certifications of an installer.

Now that we’ve cleared that up for you, let’s dive into the pros and cons of the tank and tankless variations so that you can make a decision.

Tank Heater

The Pros:

Relatively cheap

Simpler installation process

Able to handle hefty demands for hot water

High-quality technology

The Cons:

Shorter lifespan

Takes up more room indoors

Unsuitable for outdoor use

Not as energy efficient



Tankless

The Pros:

Energy-efficient

Heats up very quickly

More compact

Lasts longer

Can be installed either indoors or outdoors

The Cons:

More expensive

Installation takes longer

Expensive installation costs due to the intricate layout



Can’t handle quite as much water as the tank system

Choosing the Right Installer

Regardless of the type of unit you choose, it’s imperative that you find the right installer for your home to make sure that you don’t end up throwing your money away. The margin for error on such operations are rather high, so it’s important that you work with a reputable and credible service provider. You should look for their qualifications and certifications to see if they are experienced in the work you will hire them to do. While this may not be a foolproof strategy, it can still help ensure that your property will be protected if anything goes wrong during the installation process. If you’re looking for a plumbing service in Denver, CO get in touch with us today! We’re happy to provide a free quotation.

The post Tank & Tankless Water Heater Systems: What’s My Best Choice? appeared first on Plumbing Company in Denver, CO.

Dear Colby Plumbing Family,

We understand what challenges we have before us today with the outbreak of COVID-19. Please know that here at Colby Plumbing Company we take our clients and our personal safety with upmost priority. With that in mind we have taken the following precautions to not only ensure our clients safety and well-being but as well as the well-being of the entire Colby Plumbing staff.

• We have been regularly disinfecting our offices to help ensure that our entire staff is safe from the virus.
• Our plumbers regularly wash their hands to help prevent the spread of the virus.
• We regularly sanitize our trucks to ensure that we are not spreading germs.
• Our plumbers wear all required protective gear: respirator, eye protection and gloves before we enter anyone’s house to ensure germs are not spread throughout your home.

Thank you so very much for using Colby Plumbing and trusting us to take care of you and your home’s plumbing needs. Please reach out to us if you have any further questions or concerns for us during these challenging times.

Sincerely,



Andrew Dupree

The post Keeping Everyone Safe From The Spread Of COVID-19 appeared first on Plumbing Company in Denver, CO.

Plumbers In Denver

Getting the services of a plumber in Denver is not necessarily the thing that comes to everyone’s minds when they have a toilet or drain clogged. Instead, one of the first few thoughts of a homeowner is how will they be able to fix it on their own. Although it is acceptable to first do some troubleshooting before calling in a professional plumber for help, there is no absolute guarantee that you can fix it all on your own. There might be some instances wherein you will really need to get the services of a Denver plumber.

How Can A Plumber Help You With Your Plumbing Problems?

Plumbers are the skilled professionals that every homeowner should immediately call when they encounter any problems with their plumbing lines. Before a plumber gets into practice, he should be able to obtain a license from an accredited authority before they can perform installations, diagnosis, and repair of plumbing systems. Contrary to popular belief, plumbers in Denver are not limited only to fixing water pipelines in your home. They can also fix any air and gas pipelines, whether it is used for distribution or for its disposal. These are the bare minimums that a plumber can do for you. Now that you know what the work of a plumber is and the services they offer, let’s take a look at the instances when you should call in a plumber to help fix your plumbing problems at home.

5 Signs That You Need To Call In A Plumber For Help

Most of the time, homeowners are most likely to call for the help of a Denver plumber once they have already encountered major problems in their pipelines. For this instance, it might already constitute a major leak or something that a simple repair. Here are some warning signs that you should definitely look out for. Should you notice that these problems are slowly showing, make sure that you immediately call in a Denver plumber.

Dripping Faucets

A dripping faucet could signify that there might be an underlying plumbing problem. Almost every homeowner in Denver have already experienced a minor dripping faucet or two, but if you ask them if they have given the proper attention for it, it is most likely that they have not. For problems like this, it is easy to set it aside as something simple like a leaky valve. Most people would not think that this is not an immediate problem that would require them to call in a professional Denver plumber. However, you should know that a dripping faucet might be an indication of the onset of a serious plumbing problem.

Leaky Pipes

During cold winter months, leaking pipers are of a normal occurrence. However, these instances are still pretty common all-year-round. If, in any case, you notice that your pipes are leaking, then you should immediately call in a Denver plumber for help. This is so they can identify the root cause of the problem and have it fixed immediately. Although sealants can work temporarily, it does not solve the main cause of the problem. It only works as a band-aid solution that could wear off almost immediately. Working with a plumber, on the other hand, will help address the specific cause of the problem.

Running Toilets

Another common problem that most homeowners almost do not take notice is when their toilets are running. When you find it hard to flush, or if the toilet is continuously flushing even if it is not in use, it could present an underlying plumbing problem that has to be addressed immediately. A running toilet can waste up to 200 gallons per day. This problem will not only cost you an additional amount for your water bills, but you are also considered to be a contributor to water waste.

Low Water Pressure

If you have been living in your home for quite some time or that it has not been remodeled for about 10 to 15 years, you might encounter low water pressure in your home. The problem could be with the new showerhead you just bought, which is not exactly compatible with the type of water pipelines that you have. Worse, it could be from a hidden leak in your home’s pipes. Since there is a hole somewhere along the pipelines, even if you have an optimum pressure coming from the water source, the endpoint of the line could still receive lower water pressure. It is best to check with a credible Castle Rock plumber on what is the exact problem for this. There are various reasons that can contribute to why there is a low water pressure. Checking in with an expert will help identify the exact reason for the problem.

Water Heater Problems

There is nothing more relaxing than having a hot shower after a long day at work. Most people, especially those who live in colder areas, would need a water heater for them to survive a bathing session. Even if the cause of a water heater problem might be from a faulty technical circuit, or from the water source itself, there is nothing that a professional plumber cannot fix.

Work With A Reliable & Licensed Plumber In Denver

There are a lot of plumbers in Denver that you can choose from to work with. You should always work with a professionally licensed plumber in Denver when hiring a plumber for any plumbing problem. Whether you are looking for a plumber to help with a clogged drain or toilet, water heater problems or leaky pipes, always do a little resaearch on local plumbers in Denver before picking one. You should always check out their website for local reviews and the plumbing services they provide to Denver residents. 

The post Plumbers In Denver: When To Call A Professional Plumber For Help appeared first on Plumbing Company in Denver, CO.

Water Heater Repair

If you are looking to have your water heater systems fixed, the first thing you should do is learn about as many contractors as possible. There may be a lot of companies that give their services for various plumbing needs such as installation, maintenance, and repairs. Proper maintenance and checking of your home’s water heater should be done regularly since you can never be sure when your fixture will require a repair or you may be in need of an emergency plumber. Should you encounter something wrong with your heater, make sure that you get a water heater repair expert to fix these problems for you.

It is important that you ensure your heating device is in good condition. You can do this by looking for a certified technician to answer your repair needs. Since there are a lot of credible contractors in your area, use this to your advantage to compare and decide which one can offer the best service. Before choosing the best HVAC repair company, you should first be able to point out that there is something wrong with your heating system. Here are the usual signs of a broken water heater.

You Only Have Cold Water

In cold areas, it is a must to have a water heater. It is not usually pleasant to use cold water when bathing, especially during those winter months. Being able to have accessible hot water in your home will benefit everyone. It is important for you to get your water heater fixed should you notice that there is only cold water running from your faucets. Two possible reasons why this may happen are broken thermostats or leaking ductwork somewhere inside the water heater’s system.

Your Water Gets Warm, But Not Hot Enough

In some cases even if you have a proper flow of water at home, there is a possibility the water is just lukewarm and may not get hot enough for your liking. The reason for this is due to the thermostat setting or something wrong with the entire heating mechanism altogether. Usually, this will mean that your heating system may be just slightly damaged and not damaged enough to warrant an entire replacement. Since it is still functioning, you should opt to get it repaired. You just have to know which repair experts will be able to deal with this kind of situation. It will be better if they have worked on the same type of problem or the same type of unit before. This ensures they have experience with the issue and have an idea of how they can address the problem.

Leaks Around Your Water Heater

If you notice water leaking from the pipes or on the sides of your water heater, you probably have an issue with leaking water. Leakage is one of the more common water heater problems. Depending on the source of the leak, a leaking water heater could mean the internal failure of the unit and will need immediate attention. You have to act on it as soon as possible because the problem may affect the pressure of the water as well. So, before the situation gets worse make sure to call in an expert to have your system repaired. Do not underestimate what may seem like a small leak. Remember that these small leaks can eventually turn into larger and more serious ones. It will be better for you if you address it early enough to prevent further damage. This will also greatly affect the efficiency of your water heater. With the presence of leaks, no matter the size, it will definitely result in the lowering of the volume of water that you are going to get.

The Hot Water Is Rusty

Today’s water heaters are far more energy-efficient and economical than before. Though you can choose an expensive water heater with larger capacities and possibly with a different source of energy, there are many water heaters that are reasonable in price and more affordable. The issue with cheaper water heaters is that they are more prone to producing hot water that is rusty. Although this can be avoided by opting for a pricier device, many people may be looking for a budget-friendly solution that will limit them to getting a water heater of higher quality. If you are one of those who chose a cheaper option and are currently experiencing rusty hot water, you should call in an HVAC repair expert to help you with this problem. You should not worry about having to get a new heater since there is an expert who can surely fix this for you.

These Are The Things That You Can Encounter With Your Water Heater Repairs

There is nothing more enjoyable in the cold winter months than being able to sit and enjoy a hot cup of coffee or a nice hot bath. However, this will not be possible if you have issues with your water heater. So before you get to this point, you have to make sure that your heater is working correctly. Should you have any problems with it, make sure that you get the services of the best water heater repair expert in your area. Do not try to handle it on your own as you may encounter several issues along the way. Trust that the experts that you are going to employ will do a great job of repairing your water heater.

The post Water Heater Repair: Signs That You Need To Get It Done appeared first on Plumbing Company in Denver, CO.

Emergency Plumber

There are a lot of instances wherein you would need to get the services of an emergency plumber. Many plumbers are booked days in advance. Generally, you would have to book an appointment beforehand. However, there are some cases wherein you would really need to have to get the services of an emergency plumber.

There will be times wherein this is considered to be a rare occurrence. Not everyone knows the basics of any home repair, particularly in plumbing. Even if one is familiar with the steps that they have to take, it may also not be advisable to do since they do not have the complete materials, safety equipment, and replacement parts to have the problems fixed. The solution for this is fairly simple; you can call in an emergency plumber for help. This is the part wherein you do not need to have an appointment set beforehand. All you have to do is to simply phone in the plumbing repair company that you would want to hire, tell them what the current situation of your plumbing system is, and expect that they will be in front of your doorstep soon.

For emergency plumbing cases, it will not matter what time of the day you will need the plumber’s services. There are plumbing companies that offer 24/7 emergency plumbing repair services to its customers. This means that should you need the expertise of a plumber in the middle of the night; you do not have to wait until the next business day just so you can call a plumber for help. Instead, these companies have their own dedicated lines for emergencies. This is exactly the reason why you should not pass on getting the services of an emergency plumber in your area.

Now that you know that there are emergency plumbing services that you could avail of any time let’s take a look at the common problems that would require you to get one.

Frozen And Broken Pipes

The pipes in your home are there for a reason. Even if you cannot see it since these are hidden beneath the structure of your home, it serves a vital purpose. Without it, you will not be able to shower, wash your clothes, flush the toilet, sanitize, or wash the dishes. Pipes are essential for the delivery and transport of the liquids you need in your home. Pipes also cannot function efficiently and effectively when they are not connected in series. It would be better for the overall performance of your plumbing systems if all pipes that are connected in series are all good. Once there is a problem with one, then expect that you could encounter some serious problems that need to be addressed as soon as possible.

The major problem with any pipe connection is that these may be frozen or broken, especially during the winter season. You may not see it as an immediate problem that needs to be addressed, but broken or frozen pipes can bein to gust with water and sewage, leaving a chaotic and nasty mess inside and outside your home. The last thing that any homeowner would want to have in their home would have to be dirty sewage water flooding the insides of their home. If this is the problem you are faced with, you have no choice but to avail of the services of an emergency plumber right away. Failure to do so might leave you with several complications and major accidents in the long run.

Leaking Pipes

Frozen and broken pipes are not just two of the factors that you should look out for. At the same time, you should be aware of whether or not your pipes are leaking. A leaky pipe could come from a small hole on the pipe that is brought about different factors. You should not take a small leakage for granted as it can significantly raise your water bills. Aside from this, a leaky pipe can also cause major damage to the foundation of your home, which they would need to be repaired for you to be able to maintain your home’s structural integrity. Although it is extremely easy to ignore leaking pipes simply, you would still have to consult with a plumber regarding this problem. If left unrepaired for so long, the pipes can be the cause of the destruction of the whole plumbing system of your home.

Water Heater Repair And Replacement

One of the smallest things in life that most people take for granted would have to be the availability of warm or hot water. At the end of a tiring day, nothing beats a hot shower. But how are you exactly going to do this with your water heaters broken? A water heater and the system it is connected with is not something that is simple to deal with. You would have to have extensive knowledge about its connections, with both its plumbing and electrical components. This should be a clear indication for you that a simple DIY fix will not work. You will really have to call a plumber to help you fix or replace your water heaters.

Look Out For These Possible Signs Of A Plumbing Problem

When you are dealing with a plumbing problem, and you think that you would really have to get the services of a professional, it is extremely important that you call in an emergency plumber to help you with this kind of case. Fixing plumbing problems should not be something that you should do. Instead, you should call in the right set of professionals that can work out with these problems effectively and efficiently. Skip the stress of trying to figure out solutions that you can do. Leave these kinds of plumbing jobs to the credible and licensed plumbers in your area.

The post Emergency Plumber: Signs That You Need To Get The Services Of A Plumber appeared first on Plumbing Company in Denver, CO.